A Rare Photo?

A busy week working flat-out but not a lot to show for it, sometimes we have weeks like that and we expect them at certain points of a restoration. But like all things, it’s all in the prep work that takes the time. This is where our work is instantly recognisable from some of the other restorers out there. We will start with the Herts clone as we have been busy on the underside so nothing is really seen from the outside.

Hertz Clone

We had cut the rear quarter vents out and glass fitted in their place which is getting ready for interior paint. We were then also asked to remove the power assisted steering and go back to the manual set up. Of course this means things like the centre link would need to be replaced along with Shelby quick steer pitman arm and idler. We also fitted a new alloy oil sump while we were at it.

As we have had to change the steering setup and componants we set up a default geo for the wheels and steering. Then comes a road test and few miles added then a further fine tune re-geo once things have bedded in and settle down.

The Onion

The Onion has taken a chunk of time up in the body shop where we are at critical point on the build, the rear quarters. The back of the car has been built up and a the panels are clamped in place with an odd tack weld to see the fit for the rest of the car. The doors will need to align with the rear quarters, which in turn are aligned to the cowl, the fenders then the hood. This is all on and off again a few times to get the gaps within our own tight tolerances. Many of which will be better than the original gaps when it left the factory in the first place. One of the few original parts we have to work from is the back of the trunk which will need to fit to the new metal. This gives us a good reference point to go with our initial measurements from the car before it was dismantled.

The interior metalwork is all painted with red lead oxide for rust proofing as we go along.

The ‘B’ pillars are the strength and also the start point as such for the panel positions.

In effect this car is being built from the ground up without the original Ford build jigs. Difficult? Oh yes, but the bear likes a challenge.

Heart warming story from the net

Two siblings from San Antonio, Texas are making headlines around the country after giving their father a very special and emotional present. Jake and Jeni Ryan gave their father, Wesley Ryan, the very same 1993 Ford Mustang he sold 17 years ago to cover the expenses of his wife’s cancer treatment. The white Ford Mustang played a big role in the family as Jake and Jeni rode in it when they were toddlers. When their mother was diagnosed with ovarian cancer in the early 2000s, the Mustang was listed for sale and the profits helped cover some of the towering medical expenses. The Drive contacted Jake to find out how he was able to reunite his father with his former car, to which he answered: “I just so happen to search the good ‘ol internet and wandered onto Craigslist, and I came across the car. Emailed the previous owner, spoke for maybe 5-10 mins, and struck a deal. Flew to the owner’s place, which was about 1.5 hours away from me, and rolled her up on the trailer.”

A Facebook post that read: “I know how much it broke him in half seeing that car drive away from him. A day I’ll never forget. Well… She’s back home pops and here to stay this time. Looking forward to building this car with you this time instead of being in a booster seat looking out the window.”

Currently, Laura Ryan is cancer-free, and the Mustang is once again with its original owner. Back when Wesley Ryan first had the Fox Body he affectionately named it Christine after the Stephen King story about a demonically possessed car. Jake told The Drive that the car carries a 347 cubic-inch stroker engine that Wesley had installed in the ’90’s. While the Mustang isn’t currently running, Jake assures us that the bodywork and interior show little signs of wear. When asked what he wanted to do after getting it in running order, Jake replied: “Drive it till the wheels fall off, so I can rebuild it again.” A double great story from ‘The Drive’, the wife is in remission and the Mustang is back with the original owner. Just brilliant.

Stop Press;

Earlier today (a few hours ago in fact), Yogi was at an American Car show in Stonham Barns in Suffolk. Here he was seen with is menacing ’69 Mach1, we are now in possession of a very rare photo of the bear himself CLEANING his car. 😀

As ever the Yogi mobile got a lot of attention and one person even asked him if it was the “Mustang Maniac Demo Car?”  Yogi didn’t look to impressed to say the least, he just growled ‘no, it’s mine’. The conversation was over as quick as that. He enjoyed himself being out of his workshop cave today.

PS, ‘Yogi, you missed a bit’ 🤣🤣🤣

Lost Boxes Of Parts

This week we find Adam in the office with a big grin on his face, why? Well he had found a couple of boxes of parts that he had forgotten about. He rediscovered them while trying to make more space for some brand new stock items which we will get to a little further down the post. But first we have the Park & Pic.

Park & Pic:

This is Andy Hedley’s car that we have looked after for a while now. Andy has used this car a couple of times now for Beaujolais Run and also uses it for Charity work along with some sponsors too. So that’s a big thumbs up from Mustang Maniac.

Customers Cars:

Yogi has been working on his project; “The Onion” so far has been stripped to nothing and we have prepped the old parts we can keep with some self etc primer after some rust treatment. We have the new outer panels in boxes standing ready for fitting.

The car is not welded together with the major parts and only clamped for an idea of fit. But this is the time-consuming part as a millimetre out here or there can make a panel gap look wrong.

From the rear the same principles are applied.

Remember only the yellow etched sections are the original retained parts! This is a huge rebuild and working with just boxes of bits now to remake the car.

WebShop

We would to thank those of you for the verbal and email support we have gotten over last week’s post for the Terms and Conditions. At the top of the blog we mentioned that Adam had a big grin when he found the boxes of parts in the corner of the stock room by the office. Yes there was some new parts in there, but also some old parts he had purchased as a bulk buy a number of years ago from a Ford dealer.

These parts are going into stock too, if you are looking for those elusive original parts.

Aldan American suspension Kits – UK Supplier:

We mentioned a few weeks back that Adam has some exciting news coming soon and to watch this space about some amazing 1967 – 1970 Mustang parts. That space is now filled with the first batch of supplies and the important news that Mustang Maniac are now UK Suppliers for Aldan American suspension parts. This modern-day technology for suspension parts brings the Classic Mustang bang up to date for adjustable and customised road holding for the car and your driving style. The example here is the coil over kit for the front, with fully adjustable up or down settings which is supplied with the correct tools to adjust them. The kit comes with a full in-depth fitting guide to take the new shock tower tops.

We have scanned the sales leaflet for you here to see the range that is available for the classic Mustangs.

For further details give Adam an email at:  adam@mustangmaniac.co.uk or check the WebShop for more details as soon as we get them on there.

Peeling Off The Layers

The “Onion” Mustang has picked up a few interested comments, and yes we can confirm that we will bring the full restoration to you. Just like the “French” Mustang or the “Mastic Mustang” the car was in a bit of a mess should we say, but now they look absolutely stunning. This is again a big project from the ground up. So we kick of the post with the Park & Pic article:

This is Paul Todd’s Mach1 which has been restored using as much of the original car as possible, the paint job was done by the man himself. The car has had a set of our Magnum alloy rims on the car and they really suit it. The tyres are yet to be decided but that is just minor details. The subtle touch is the red centre caps to match the hood intakes!

The car needed a few minor additions and Yogi was seen prowling the premises and was collared into fitting some new wiper blades.

Customer Cars:

67 Fastback. Last week we showed you the poor state of the suspension arms that have now been replaced. This week Yogi has completed the under hood wiring loom and looks stock.

We are awaiting further instructions whether to continue with the rest of the restoration or hand the car back as she is, which was plan A. 🙂

The Onion Mustang

We start this update with a little selfie time that was uploaded to Facebook forum click here for the link. The guys getting stuck into the Onion and had a tea break feeling pleased with themselves.

The car has had the floor pans cut away, the front and the rear cabin sections. The Jig was custom-made by Yogi to make sure everything goes back at is should with the original factory jig holes being used. Now we can start to build her up layer by layer. Already she looks totally different.

The dash section was fine and will be used for the basis of the panel fit with the rear cabin section.

With the floor pan now out of the way, the new floor pan could be laid on the jig and married up to the jig and the existing parts.

A new sill was needed along with more metal work.

That leaves replacing the front inner metal work.

Off course none of this can be welded in place yet and is clamped and lightly tack welded just for now until we are happy with the measurements taken of the old parts. Watch this space to see how it all comes together.

WebShop Stock

We get asked now and again if we can get some Rostyle wheels for the early UK Fords. Well we listened and have a batch in stock. We have sold some already and have some left. Shall we keep them as stock or make this a one of batch? Let us know! These wheels we part of original kit for MGB, Rover and of course the early Fords. What we have here are the 15″ version and we love the look of the wheels.

Competition:

You only have a couple of hours to go before the competition deadline runs out. It’s not official this, so don’t tell Adam, but if you send them to mustangmaniacuk@gmail.com after the Midday cut off until this evening, I will sneak them onto the little stack on Adam’s desk.